Reinitialize your Holosun EPS Carry Red Dot Sight

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected issues. Fortunately, resetting your Holosun is a straightforward process that can be completed in just a few procedures.

Begin by ensuring your red dot sight is powered on.
Find the small reinitialize button on the side of the unit.
Employ a paperclip to depress the reset switch for approximately 7 moments.
Let go the switch and your Holosun EPS Carry Red Dot sight will power cycle.
Your red dot sight should now be reverted to its factory settings.

Restore Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, find the tiny button on the rear of your optic. Then, keep pressed it for around five seconds until you see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for consistent targeting.

restore Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory how to factory reset Holosun EPS Carry red dot reset on your Holosun EPS Carry, follow these simple steps:

Simultaneously press and hold the power button for approximately 10 seconds.
An indicator will flash, indicating that the reset is being performed.
Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and confirm your sight's functionality. If you encounter any further troubles, don't hesitate to reach out to their technical assistance.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

Initially, Energize your Holosun EPS Carry by pressing the power button.
Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
During continue holding these buttons, tap the power button once.
A message will show a confirmation prompt indicating that the reset process is initiated.
Permit the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Restore your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will restore your sight to its initial settings, clearing any custom configurations you've made. To execute this reset, follow these straightforward steps:

First, find the reset lever on your EPS Carry.
Next, press a small object, like a pen tip, to push the reset lever.
During keep the reset button pressed, turn your EPS Carry.
It will flash a message confirming that the reset is complete.

Once the reset is complete, your EPS Carry will be back to its factory settings.